操作人員在使用自動化焊接設備的過程中，要注意使用方法，并做好保養，以免設備出現損壞，影響正常工作。下面我們就來看看延長山東自動化焊接設備使用壽命就要做好哪些事項。

During the use of automatic welding equipment, operators shall pay attention to the use method and do a good job of maintenance to avoid damage to the equipment and affect the normal work. Now let's take a look at what needs to be done to extend the service life of Shandong automatic welding equipment.

1.定期做好檢測工作。比如查看設備通電時，冷卻風扇的旋轉是否平順;是否有異常的振動，聲音和氣味;氣體是否有漏泄;電焊線的接頭及絕緣之包扎是否有松懈或剝落;焊接電纜線及各接線部位是否有異常的發熱現象等。

1. Carry out regular inspection. For example, check whether the cooling fan rotates smoothly when the equipment is powered on; Whether there is abnormal vibration, sound and smell; Whether the gas leaks; Whether the binding of welding wire joints and insulation is loose or peeling; Whether there is abnormal heating phenomenon in the welding cable and wiring parts.

2.由于設備是強迫風冷的，很容易從周圍吸入塵埃并積存于機內。所以我們可以定期對其進行清理，以免影響設備的正常使用。尤其是變壓器、電抗線圈及線圈卷間的空隙縫和功率半導體等部位要特別清拭干凈。

2. As the equipment is forced air cooling, it is easy to inhale dust from the surrounding and store it in the machine. Therefore, we can clean it regularly so as not to affect the normal use of the equipment. In particular, the gap between transformers, reactance coils and coils, power semiconductors and other parts shall be cleaned.

3.定期檢查電力配線的接線部位。檢查入力側、出力側等部位，以及外部配線的接線部位，內部配線的接線部位等部位的接線螺絲是否有松動，生銹時要把銹除去使接觸導電良好。

3. Regularly check the wiring position of power wiring. Check whether the connection screws at the input side, output side and other parts, as well as the connection parts of the external wiring and the internal wiring are loose. Remove the rust to ensure good contact and conductivity.

4.自動焊接設備長期的使用難免會使外殼因碰接而變形，生銹而受損傷，內部零件也會磨損，因此定期對零件進行更換，修補外殼，并對絕緣劣化部位進行補強。不好的零件在做保養時盡量全部一次更換以保證設備的性能。

4. The long-term use of automatic welding equipment will inevitably cause the shell to be deformed, rusted and damaged due to contact, and the internal parts will also be worn. Therefore, the parts shall be replaced regularly, the shell shall be repaired, and the insulation deteriorated parts shall be reinforced. The bad parts should be replaced as soon as possible during maintenance to ensure the performance of the equipment.

5.對導電嘴定期進行檢查。由于磨損導電嘴的孔徑變大，就會引起電弧不穩定，焊縫外觀惡化或粘絲(回燒);導電嘴末端粘上飛濺，送絲會變得不平滑;導電嘴擰得不緊，螺紋連接處會發熱而焊死。

5. Regularly check the conductive nozzle. As the aperture of the worn conductive nozzle becomes larger, the arc will be unstable, the appearance of the weld will deteriorate or the wire will stick (burn back); The end of the contact tip is stuck with spatter, and the wire feeding will become uneven; If the contact tip is not screwed tightly, the threaded connection will be heated and welded.

為了避免自動焊接設備在使用中出現故障問題，操作人員一定要注意使用方法，并做好保養，這樣也能及時發現問題，延長其使用壽命。關注我們http://www.fangzh.cn帶您了解更多相關內容！

In order to avoid the failure of automatic welding equipment in use, the operator must pay attention to the use method and do a good job in maintenance, so that problems can be found in time and the service life can be extended. Follow us http://www.fangzh.cn Learn more about it!